150mm (6") Snap Fit Aluminium Beaded Half Round Fascia Bracket
Sentinel Beaded Half Round Snap-fit Extruded Aluminium Gutter Fascia Brackets are available in Mill Finish and in PPC (Polyester Powder Coating)
Please note - All aluminium gutters and fittings are specially ordered and are non-returnable. All PPC items are coated external face only.
Manufacturer: ARP
Product Code: 6BHRBF
►Return to product list
From our site to your site as quickly as possible
Delivery Charges
We can offer a free standard delivery service on specific ranges if your order reaches the thresholds stated below (Exclusions Apply). Orders under thesholds below will be charged a delivery fee. All delivery charges are calculated at basket and are dependent on the items ordered. Charge is based on delivery to mainland UK excluding Scottish Highlands and Islands where additional charges may apply – this is determined by the courier delivering the goods. For deliveries to these areas, we are happy to provide a free quotation upon request.
Free Delivery Thresholds
Brett Martin Ranges - Orders over £1600 (Ex VAT)
ARP Ranges - Order over £1200 (Ex VAT)
Free Delivery Exclusions
All Lindab Products
All Pam Saint-Gobain Products
Delivery Dates and Times
Please see here for latest estimated lead times.
Whilst we will make every effort to deliver your goods within the stated/requested time frame, we cannot guarantee availability from the manufacturer or the manufacturer's delivery schedules, so we would recommend not to start/schedule any work until the goods arrive. Due to logistics of various couriers and suppliers we are unable to give times of deliveries. Deliveries can take place from as earlier as 07:30 right up to 18:00 depending on the courier/haulier and considering local traffic etc.
Signing For Your Goods
All deliveries should be signed for, and we would politely request that you sign and clearly print your name so that in the unlikely event that there are any discrepancies we will have a person to contact. If a signature cannot be obtained, we will try to leave the goods in a safe location, but we cannot be held responsible for shortages or damages where goods have not been signed for.
Accepting Your Goods
Please thoroughly check you have received all expected items and any shortages/damages must be reported within 48 hours of delivery. Large or palletised goods will be delivered to a hard standing area only. The Customer shall be solely responsible for the unloading of the Goods and the Seller shall not be liable for any damage that occurs during such unloading.
Delivery Vehicle
If goods aren't sent buy our own vehicles, they are sent buy reputable carriers such as Tufnell's, DX, DPD and Parcel Force. Heavier goods may be delivered by larger vehicles and will be off loaded by means of a pump truck; the driver will then deliver by means of the pump truck as close as possible to the property whilst remaining on a hard standing surface.
Multiple Deliveries
Sometimes goods can be delivered in multiple deliveries, this is due to some items coming direct from suppliers or our own yard. If this is the case, multiple charges will be combined at the basket.
Good Advice
Please do not arrange any labour until your materials are on site as we are unable to compensate you in the event of a late delivery.
If you have ANY questions about our products, or want to give us some feedback about your shopping experience with us, please feel free to contact us on 03302 230 275 or email our customer services team
*excluding VAT
Sentinel Aluminium Beaded Half Round Snap Fit Gutter And Fittings Installation And Technical Guides
It is advised that you ensure the fixing background (e.g fascia board) is securely fixed, level and able to support the weight of the gutter at full capacity and that the roof overhang is correct – see gutter position.
Buildings without fascias may need a different type of bracketry. ARP offer a range of brackets to suit most applications. ARP offer side and top fix rafter arms as well as rise and fall brackets. The latter do not meet current BS/EN load requirements so advice should be sort on the parameter of their use.
1-Start by deciding whether to fit the gutter level or with a fall to 1:600. Fit a bracket at each end of a run. Position brackets correctly for an angle or stopend.
2-Bracket positioning for the angle and bracket to take the gutter length should be 150mm.
3-It is recommend fixing brackets every 750mm and using an additional bracket for each
outlet or angle. Ideally using a string line or laser level between the two brackets, set out intermediate brackets at maximum centres of 750mm.
4-With the use of a plumb or laser line, position outlets over gullies and support with at least
one bracket. Also include a bracket per angle (internal or external).
5-When fitting outlets and angles tuck the rear face of the gutter underneath the roof finish.
Locate the gutter into the fascia bracket and then clip the front edge down into position.
After fitting outlets and angles, proceed with fitting the gutter lengths using the same method.
6-Ensure that all fixing surfaces are clean and dry. Placing the union into the groove in the rear face of the gutter and clip down into place on the front edge.
7-Trim 4-5 mm off top of nozzle so it fits snuggly into the large holes in the base of the union, inject the special low modulus sealant supplied into one of the large holes in the bottom of the union until the sealant appears at both of the smaller holes at the rim of the union.
Repeat the action on the other large hole.
8-Ensure you apply the sealant gently to ensure the void is fully filled.
Clean off any excess sealant and then use the same process for every joint until the work is completed.
Any cut lengths should be de-burred and touched up with touch-up paint supplied prior to installation. For more information or further assistance, please contact us.
Jointing:
Aluminium has a coefficient of expansion equal to 0.00002348mm per °C on average, this equates to just over 1.4mm per metre on a temperature range of -20°C to +40°C. Typically a 3mm to 4mm expansion gap between the ends of the gutter sections is advisable.
ARP recommend and supply Arbosil 1096 Low Modulus Silicone sealant and it is essential that this or a direct equivalent is used to seal the joints as this will ensure a strong mechanical bond that withstands the forces associated with thermal movement.
It is important to observe the sealant manufacturers guidelines concerning application and curing during cold or damp weather conditions & that before assembling the joint all surfaces are clean & free from grease, acetone applied with a soft cloth and wiped dry is recommended.
Cast Half Round gutters have a Spigot and Socket overlap arrangement that are secured using M6 x 30mm aluminium bolts, neoprene washers and nuts.
Having sited the gutter, apply 2 x 6mm beads of Arbosil 1096 Low Modulus Silicone sealant to the gutter socket. (Fig 2.) The two surfaces can then be brought together, the bolt inserted applying sealant to the thread and round the slot in the union, tighten the joint until some sealant emerges and a feeling of resistance is achieved leaving a 3mm sandwich of sealant. Excess sealant should then be removed.
Fig 2.
Composition and Manufacture:
‘Legacy” Cast Beaded Half Round Gutters are manufactured from Aluminium alloy LM27 to BS1474: 1972 & the product complies to, or exceeds all relevant standards.
Special fittings for the gutters using fabrication methods involving cut, mitre and welding techniques can be provided.
Finish:
Mill Finish Aluminium or Polyester Powder Coated to a range of BS or RAL Colours
Model Specification:
ARP heavy grade ‘Legacy’ Gutters and fittings to BS 2997 (EN612) using LM27 alloy aluminium in accordance with BS1474: 1974. Profile to be Half Round, size 100mm (3mm),114mm (3mm), 125mm (4mm) & 150mm (4mm). Materials to have factory applied Polyester Powder Coat to all significant surfaces in accordance with BS EN 122026 Matt/Satin/Gloss* finish, or alternatively plain aluminium Mill Finish. All to be supplied by Aluminium Roofline Products Ltd.
Joints to be loose union connector sealed by application of Arbosil 1096 Low Modulus Silicone Sealant and fastened by M6 x 30mm bolts, neoprene washers and nuts in accordance with the manufacturer’s specification and guidelines. Gutter to be fixed by fascia brackets at 915mm centres with supplementary brackets at or near fittings. Fixing for brackets to be 5mm x 25mm countersunk/domed head stainless steel screws (dependant on substrate).
ARP Sentinel Beaded Half Round Gutter Installation Guide
ARP Sentinel Beaded Half Round Gutter Technical Guide
Standard Aluminium BS/RAL Polyester Powder Coating Colour Options
Drainage Central can provide your aluminium order either in a plain aluminium mill finished or Polyester Powder Coated (PPC).
Save time on site by having your order delivered already painted to a colour of your choice.
You can select from any BS/RAL colour.
If you would like a colour swatch sent out please fill in the contact us form
here and we will get one to you as quick as possible.
ARP can provide a variety of colours and finishes see below for the standard colours provided.
For other colour options please call us on 03302 230 275 or email us at [email protected].
Please note the image shown below is just an example and a colour swatch is recommended to show true representation.
For any further details please call our customer service team.