63mm (2.5 Inch) Circular Aluminium Adjustable Downpipe Bend 800-1000mm

Colonnade Round Swaged Aluminium Downpipe Two Part Offset Bends are available in Mill Finish and in PPC (Polyester Powder Coating).

Please note - All aluminium gutters and fittings are specially ordered and are non-returnable. All PPC items are coated external face only.

Manufacturer: ARP
Product Code: 2RSN100/2

►Return to product list

From our site to your site as quickly as possible

Delivery Charges

We can offer a free standard delivery service on specific ranges if your order reaches the thresholds stated below (Exclusions Apply). Orders under thesholds below will be charged a delivery fee. All delivery charges are calculated at basket and are dependent on the items ordered. Charge is based on delivery to mainland UK excluding Scottish Highlands and Islands where additional charges may apply – this is determined by the courier delivering the goods. For deliveries to these areas, we are happy to provide a free quotation upon request.

Free Delivery Thresholds
Brett Martin Ranges - Orders over £1600 (Ex VAT)
ARP Ranges - Order over £1200 (Ex VAT)

Free Delivery Exclusions
All Lindab Products
All Pam Saint-Gobain Products

Delivery Dates and Times

Please see here for latest estimated lead times.
Whilst we will make every effort to deliver your goods within the stated/requested time frame, we cannot guarantee availability from the manufacturer or the manufacturer's delivery schedules, so we would recommend not to start/schedule any work until the goods arrive. Due to logistics of various couriers and suppliers we are unable to give times of deliveries. Deliveries can take place from as earlier as 07:30 right up to 18:00 depending on the courier/haulier and considering local traffic etc.
 

Signing For Your Goods

All deliveries should be signed for, and we would politely request that you sign and clearly print your name so that in the unlikely event that there are any discrepancies we will have a person to contact. If a signature cannot be obtained, we will try to leave the goods in a safe location, but we cannot be held responsible for shortages or damages where goods have not been signed for.
 

Accepting Your Goods

Please thoroughly check you have received all expected items and any shortages/damages must be reported within 48 hours of delivery. Large or palletised goods will be delivered to a hard standing area only. The Customer shall be solely responsible for the unloading of the Goods and the Seller shall not be liable for any damage that occurs during such unloading.
 

Delivery Vehicle

If goods aren't sent buy our own vehicles, they are sent buy reputable carriers such as Tufnell's, DX, DPD and Parcel Force. Heavier goods may be delivered by larger vehicles and will be off loaded by means of a pump truck; the driver will then deliver by means of the pump truck as close as possible to the property whilst remaining on a hard standing surface.
 

Multiple Deliveries

Sometimes goods can be delivered in multiple deliveries, this is due to some items coming direct from suppliers or our own yard. If this is the case, multiple charges will be combined at the basket.
 

Good Advice

Please do not arrange any labour until your materials are on site as we are unable to compensate you in the event of a late delivery.
 
If you have ANY questions about our products, or want to give us some feedback about your shopping experience with us, please feel free to contact us on 03302 230 275 or email our customer services team
 

*excluding VAT

Colonnade Aluminium Swaged Round Downpipe And Fittings

The Colonnade Range of Aluminium Swaged Circular Rainwater Downpipes are available in either a Mill finish or PPC finish.

The Colonnade Aluminium Round Swaged downpipe system is formed from extruded 6060 T4 aluminium in various sizes (63mm,76mm, 101mm and 150mm) and is supplied with a complete range of accessories including Aluminium Swaged Round Offsets Bends, Aluminium Swaged Round Bends, Aluminium Swaged Round Shoes, Aluminium Swaged Round Downpipe Clips.

How Do I Install Aluminium Swaged Downpipe And Fittings?

We advise that you ensure the fixing background is in good condition and will support the downpipe and that there are sufficient clips/brackets in place to secure the load.
ARP manufactures 3 different pipe systems (Swaged, Flush joint and Cast Collared) and the below instructions are applicable to all systems unless specifically mentioned.
When fitting Colonnade downpipes, start from the outlet and work towards the gully. Make sure you have the right combination of offsets/bends/branches and pipe to complete the installation.

Maximum fixing centres is 2 metres – using correct stainless-steel fixings and plugs for the substrate being fitted to.

1-Ensure vertical alignment between drain and pipe socket prior to installation.

2-Sealant can be applied to the inside of the pipe socket prior to installation.

Swaged and flush joint downpipes should have sealant applied to the socket prior to installation.

Cast Collared can be sealed after fitment.

When fitting flush joint downpipe, sealant can also be applied to the inside of the clip to assist in supporting the pipe.

3-Ensure vertical alignment between drain and gutter outlet.

Adjust the offset to suit the projection.

Place the offset in position from the outlet and fix the first pipe into place, thus holding the offset in position.

4- Additional pipe clips should be fitted at 2m maximum intervals.
 
Carry on installing pipes in this fashion until reaching the drain.
 
Clips to be fixed with plastic wall plugs and stainless-steel screws of a size suitable for the substrate.

5- A shoe, drain adaptor or offset may be required to terminate the pipe work into the gully.

6-As per local building regulations, if a shoe is not installed access pipes should be fitted and positioned to give suitable rodding access as required.

Any Cut Lengths Should be de-burred and touched up with touch up paint supplied prior to installation for more information or further assistance, please contact us.
 
Jointing
Where required, any use of sealant must not be carried out in wet weather or in temperatures below 5ºC or above 50ºC. All joint surfaces must be perfectly clean and dry. Only a low modulus sealant (ARP Arbosil 1096) must be used to prevent early failure.

Fixing
It is important that all fixings are suitable for both the substrate and the load. They must therefore be of the appropriate size and of a compatible material to ensure no electrolytic corrosion occurs. ARP recommends that stainless steel (preferably austenitic) screws must be used to fix downpipes or associated components.

Composition & Manufacture
Colonnade’ downpipes are manufactured from Aluminium alloy 6060 T4 to BS1474: 1972 & the product complies to or exceeds all relevant standards. Fittings for the downpipes are formed using fabrication methods involving cut, mitre & welding techniques using specially made jig & forming tools. Socket depth on all ranges is 60mm.

Model Specification
ARP heavy grade ‘Colonnade’ Swaged Downpipes & fittings to BS 2997 (EN612) using 6060 T4 grade extruded aluminium in accordance with BS 1474: 1974. Profile to be Round., size Ø63mm (1.6mm), Ø76mm (1.6mm), Ø101mm (1.6mm), Ø150mm (2.5mm) Materials to have factory applied Polyester Powder Coat to all significant surfaces in accordance with BS EN 122026 Matt/Satin/Gloss finish, or alternatively plain aluminium Mill Finish. All to be supplied by Aluminium Roofline Products Ltd. To be fastened by 5mm x 50mm (dependant on substrate) stainless steel screws, in accordance with the manufacturer’s specification & guidelines. Downpipes to be fixed at 2m centres maximum with supplementary brackets at or near fittings.

ARP Round Aluminium Downpipe with Swaged Collar Installation Guide
ARP Round Aluminium Downpipe with Swaged Collar Technical Guide

Standard Aluminium BS/RAL Polyester Powder Coating Colour Options

Drainage Central can provide your aluminium order either in a plain aluminium mill finished or Polyester Powder Coated (PPC).

Save time on site by having your order delivered already painted to a colour of your choice.

You can select from any BS/RAL colour.

If you would like a colour swatch sent out please fill in the contact us form here and we will get one to you as quick as possible.

ARP can provide a variety of colours and finishes see below for the standard colours provided.
For other colour options please call us on 03302 230 275 or email us at [email protected].

Please note the image shown below is just an example and a colour swatch is recommended to show true representation.

For any further details please call our customer service team.