The 80mm Round Stainless Steel Downpipe x 2.4m is swaged at one end which allows multiple downpipes to be push fitted together with no sealant required.

The 80mm Round Stainless Steel Downpipe Connector is used to fix two different pieces of 80mm round Stainless Steel downpipe together. Downpipe connectors are only required for offcuts.

The 80mm Round Stainless Steel Downpipe Clip is required to fix the downpipes to a wall. Clips required per 1.5 metres of downpipe. If the system is less than 4.5m in length, three evenly spaced downpipe clips should be fitted.

The 80mm Round Stainless Steel Downpipe 72 Degree Bend is used to alter the downpipes direction and can also be used to create an offset bend

The 80mm Round Stainless Steel Downpipe Swan Neck can extend the 80mm round Stainless Steel downpipe from the wall or to offset the downpipe along the wall. It is 3 pieces and can be cut on site as required.

The 80mm Round Stainless Steel Downpipe Branch is used to bring together two lengths of downpipe, in order to direct the flow into one pipe.

The 80mm Round Stainless Steel Downpipe Water dispenser is fixed at the bottom of an 80mm round Stainless Steel downpipe in order to channel the water into a gully or drain.

The 80mm Round Stainless Steel Downpipe Shoe is used at the bottom of a downpipe if it is not connected to a gully or drainage pipe. The open section should face away form the building.

The 80mm round Stainless Steel Downpipe Spigot allows you to connect your guttering to your downpipe without using a gutter outlet.

The 80mm x 80mm Square Stainless Steel Downpipe x 2.4m is swaged at one end which allows multiple downpipes to be push fitted together with no sealant required.

The 80mm x 80mm Square Stainless Steel Downpipe Connector fixes two pieces of 80mm x 80mm square Stainless Steel downpipe together. Stainless Steel downpipe connectors are only required for offcuts.

The 80mm x 80mm Square Stainless Steel Downpipe Clip fixes downpipes to a wall. Fitted per 1.5m of downpipe. Systems less than 4.5m in length require three evenly spaced clips.

The 80mm x 80mm Square Stainless Steel Downpipe 72 Degree Bend fits onto the outlet to divert the Stainless Steel downpipe. Alternatively they are push fitted onto a different Stainless Steel downpipe.

The 80mm x 80mm Square Stainless Steel Downpipe Swan Neck extends the downpipe from a wall or offsets along the wall. It is 3 pieces and can be cut on site as required.

The 80mm x 80mm Square Stainless Steel Downpipe Branch is used for both gutter and soil pipes to fix together two lengths of Stainless Steel downpipe, directing the flow into one pipe.

The 80mm x 80mm Square Stainless Steel Downpipe Shoe fits at the bottom of a downpipe if unconnected to a gully or drainage pipe. Open section faces away from the building.

The 100mm Round Stainless Steel Downpipe x 2.4m is swaged at one end which allows multiple downpipes to be push fitted together with no sealant required.

The 100mm Round Stainless Steel Downpipe Connector is used to fix two different pieces of downpipe together and are usually only required for offcuts.

The 100mm Round Stainless Steel Downpipe Clip is required to fix 100mm round Stainless Steel downpipes to a wall. Clips required per 1.5 metres of downpipe. If the system is less than 4.5m in length, three evenly spaced downpipe clips should be fitted.

The 100mm Round Stainless Steel Downpipe 72 Degree Bend can be fitted onto the outlet to slightly divert the 100mm round Stainless Steel downpipe or alternatively they can be push fitted onto a different Stainless Steel downpipe.